rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (4) stand juni 2016 rev 01 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. dc/dc-converter rs4/rd4-r10m 1.0w regulated single output we energize electronics! an acal group company we energize electronics! ? 7 pin sil/ 14pin dil package ? 1000vdc isolaton ? up to 3000vdc isolaton ? contnuous short circuit protecton ? low ripple and noise ? efciency up to 68% ? operatng temperature range: -40 ~ +85c ? non conductve black plastc case ? emi complies with en55022 class b output specification voltage accuracy: 2% line regulaton: 0.5% load regulation: from 0% to 100% load: 0.5% output 3.3v model: 1.0% short circuit protecton : contnuous ripple noise (20mhz bandwidth): 50mv pk-pk temperature coefcient: 0.02% c capacitor load: see table input specifications voltage range: 10% max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20ma pk-pk general specifications efciency: see table i/o isolaton voltage (60sec): 1000 ~ 3000vdc i/o isolaton capacitance: 60pf typ. i/o isolaton resistance: 1000m ohm switching frequency: variable 50khz humidity: 95% rel h reliability calculated mtbf : > 3.5mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: non-conductve black plastc (ul94v-0 rated) pin material: ? 0.5mm alloy42 solder-coated potng material: epoxy (ul94v-0 rated) weight case- sip: 2.7g weight case-dip: 2.9g dimmension sip: 0.76 x 0.28 x 0.39 dimmension dip: 0.80 x 0.40 x 0.27 absolute maximum ratings (1) input surge voltage (100ms)/ 5 v models: 7vdc max 12v models: 15vdc max 24v models: 28vdc max soldering temperature (2) : 260c max. emc specifications radiated-/conducted emissions: en55022 class b esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (4) stand juni 2016 rev 01 dc/dc-converter rs4/rd4-r10m 1.0w regulated single output we energize electronics! an acal group company we energize electronics! r s4 - xx xx x xx power (w) input t ype a x m code inter nal isolation (kvdc) model selection guide model number input input current output output current
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (4) stand juni 2016 rev 01 +vout +v in dc/dc converter - vin - vout emi filter input filter components (c1, l ) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. input filter components (c1, l) are used to help meet emc requirement for the module. these components should be mounted as close as possible to the module;and all leads should be minimized to decrease radiated noise. 5.exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 6.operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. efficiency vs output current 100 90 80 70 60 50 40 30 20 10 0 0% lo line nominal hi line 20% 40% 60% 80% load (%) 100% 120% efficiency vs output current 100 90 80 70 60 50 40 30 20 10 0 lo line nominal hi line 0% 20% 40% 6 0 % load (%) 80% 100% 120% efficiency(%) efficiency(%) emi filter input filter components (c1, l ) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 dc/dc-converter rs4/rd4-r10m 1.0w regulated single output we energize electronics! an acal group company we energize electronics! +vout +v in dc/dc converter - vin - vout emi filter input filter components (c1, l ) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l load c1 5v mode 12v mode 1. ripple/noise measured with 20mhz bandwidth. 2. tested by minimal vin and constant resistive load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. input filter components (c1, l) are used to help meet emc requirement for the module. these components should be mounted as close as possible to the module;and all leads should be minimized to decrease radiated noise. 5.exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 6.operation under no - load conditions will not damage these devices, however they may not meet all listed specifications. efficiency vs output current 100 90 80 70 60 50 40 30 20 10 0 0% lo line nominal hi line 20% 40% 60% 80% load (%) 100% 120% efficiency vs output current 100 90 80 70 60 50 40 30 20 10 0 lo line nominal hi line 0% 20% 40% 6 0 % load (%) 80% 100% 120% efficiency(%) efficiency(%)
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (4) stand juni 2016 rev 01 rs4-xxxxr10a1m rd4-xxxxr10a1m rs4-xxxxr10a1m rd4-xxxxr10a1m dc/dc-converter rs4/rd4-r10m 1.0w regulated single output we energize electronics! an acal group company we energize electronics! rs4-xxxxr10a1m rd4-xxxxr10a1m rs4-xxxxr10a1m rd4-xxxxr10a1m dil 14 sil 7 the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
